GPIOX Cards & Test Boards

ADCXB 2 Gsample/s A/D Converter

The ADCXB is a GPIOX card with two coherent A/D converter channels and precision 2 GHz clock source. The 10 bit A/D outputs connect to the User Logic chips on the MAP® via an in-package 4-way Demux. The channels can be used either independently or in a coherent fashion such as for the capture of Angle of Arrival information. Inputs to the card are differential but can be used in single ended mode by adding a 50 ohm terminator to one of the differential input legs. The card also has an RS232 port to allow the user to connect additional equipment for collecting such information as navigation or GPS data. The ADCXB card can be used with all SRC products that support GPIOX.

Parameter	Value
A/D Converter with 1:4 DMUX	e2V AT84AS004*
Sample Rate	2 Gsamples/second
Number of A/D Output Bits	10
Number of Demux Output Bits	40
Number of A/D Channels	1 or 2
Differential Input Impedance	100 ohms internally terminated
Single Ended Input Impedance	50 ohms internally terminated
Input Connectors	MCX female**
Maximum Input Amplitude	750 mv P-P
Maximum Input Level	+-375 mv
Full Scale Input Amplitude	500 mv P-P
Clock Frequency	2 GHz; for alternate frequencies contact SRC
Clock Frequency Stability	+- 100 ppm maximum
Clock Phase Noise
10 KHz	-120 dBc/Hz
20 KHz	-125 dBc/Hz
10 MHz	-130 dBc/Hz
100 MHz	-145 dBc/Hz
Clock Output Type	Dual differential
Phase Difference	180 +-15 Degrees
RS232	Commercial Micro D plug R/A9  Supports TD, RD, RTS, CTS signal protocol

* For current detailed specifications see e2V data sheets.

** When used with the “6U” MAPstation, jumper cables will convert these to female SSMA connectors at the front panel.

 

More Information

Download product sheet

How to Buy

 

back to top

 

IOX Camera Link Interface

The IOX Camera Link Interface is a GPIOX card that will accept three Camera Link Base connections or one Full/Med connection and one Base connection. Each Camera Link connection supports typical frame sizes and pixel depths, and dot rates, programmed by the user via the Carte™ Programming Environment. In addition to the Camera Link connections, the card can be ordered with an RS232 option to allow the user to connect to additional equipment. The IOX Camera Link card can be used with all SRC products that support GPIOX.

 

 

Parameter	Value
Camera Link	3 Camera Link Connectors support Base, Medium and Full modes:       (3) Base (independent);       (1) Full/Medium + (1) Base (independent)
Camera Link Speed	25MHz to 85MHz Camera Link connection data rates      Base - 2.38 Gbits/sec      Medium - 4.76 Gbits/sec      Full - 6.35 Gbits/sec
Image Triggering	Free Running  External Triggered Modes using CC1 through CC4
Multiple Taps	Camera Link standard multi-tap:      Full: 8 x 8-bit      Medium: 4 x 8-bit, 4 x 10-bit, 4 x 12-bit, 1 x 30bit/RGB, 1 x 36-bit      Base: 3 x 8-bit, 2 x 10-bit, 2 x 12-bit, 1 x14-bit, 1 x 16-bit, 1 x 24-bit/RGB  Additional: 4 x 14-bit, 4 x 16-bit, 1 x 48bit, 1 x 64-bit  Other configurations are programmable by the user
Image Acquisition Size	Area-Scan Digital or Line-Scan      640 x 480; 1024 x 1024; 1600 x 1200; 1920 x 1080      2048 x 2048; 4004 x 2672; 4872 x 3248  Other configurations are programmable by the user
Pixel Size	8, 10, 12, 14 or 16 bits/pixel  Mono, 8 or 10 bit RGB.
Camera   Communication	9600, 19200, 38400, 57600, and 115200  Via the Camera Link Interface
RS232 Option	Replaces one Base Camera Link connector with a Commercial Micro D  plug R/A9  Supports TD, RD, RTS, CTS signal procotols

 

More Information

Download product sheet

How to Buy

back to top

 

IOX Card

SRC’s IOX card is a GPIOX card that connects all of the GPIOX signals to two connectors. The GPIOX "A" signals are routed to connector J102, and the GPIOX "B" signals are routed to connector J103. Three voltages (+5V, -5V and +12V) are routed to the connectors J102 and J103.

• 2 Samtec 120 pin connectors (QTH-060-01-L-D-LC) (J102 and J103)

• 48 data pairs per connector (positive and negative) or; 
  96 single-ended data per connector (J102 and J103)

• 1 clock pair per connector (positive and negative) or; 
  2 single-ended clocks per connector (J102 and J103)

• +5V, -5V & +12V per connector (J102 and J103)

 

More Information

Download product sheet

How to Buy

back to top

 

GPIOX Test Board

SRC’s GPIOX Test Board plugs into the GPIOX connector and provides connectors for logic analyzers, scopes and signal generators. This allows the engineer to both monitor signals from and inject signals into the USER logic. There are also two pushbutton switches and eight DIP switches to provide input into the USER logic, and five LED indicator lights that are controlled by the USER logic. Finally there is a 4 Mbit Flash PROM that can be programmed with a JTAG download cable. The data stored in the PROM can then be read by the USER logic.

 

• 80 single ended data signals or;
  40 data pairs (positive and negative)

• 10 single ended clocks or;
  5 clock pairs (positive and negative)

• 10 8x2 data headers (.025" square, .100" spacing)

• 5 2x1 clock headers (.025" square, .100" spacing)

• 2 pushbutton switch inputs

• 8 DIP switch inputs

• 5 LED indicator lights

• 1 4Mbit flash PROM

• 1 JTAG connector (Samtec IPL1-103-02-F-D)

 

More Information

Download product sheet

How to Buy

back to top